Stone Hand Held Machines

the version with fairing and 2 hours of autonomy
always the version with fairing and 2 hours of autonomy
the version without fairing
always the version without fairing
THREE VERSIONS AVAILABLE;
ONE WITH FAIRING AND AUTONOMY TWO HOURS OF CONTINUOUS OPERATION
ONE WITH FAIRING AND ONE HOUR OF CONTINUOUS OPERATION
ONE WITHOUT FAIRING WITH ONE HOUR OF AUTONOMY, THE LIGHTEST, SPECIFIC FOR VERTICAL WORKS
THE FIRST TWO VERSIONS HAVE REVOLUTION ADJUSTMENT AND REVERSE OF THE ROTATION SENSE
THE LATEST FIXED SPEED VERSIOR
THE REVERSE OF THE DIRECTION OF ROTATION, COVERED BY OUR PATENT, ALLOWS TO SHORTEN THE SANDING AND POLISHING TIMES BY AT LEAST 30%
BECAUSE BY ALWAYS REVIVING THE TIPS OF THE ABRASIVES AND POLISHING WITH EVERY REVERSE, WE HAVE A GREATER ACTION
the version with fairing and 1 hour of autonomy
THE BATTERY-POWERED FLEX WORKS WITH ITS OWN BATTERY ON BOARD, SO IT IS NOT BOUND TO ANY CABLE.
IT HAS AN AUTONOMY OF 1-2 HOURS OF CONTINUOUS OPERATION, DEPENDING ON THE MODEL, THEN RECHARGES IT.
COMPARED TO THE SINGLE FLEX IT HAS DIFFERENT CHARACTERISTICS:
WEIGHT ABOUT 3 KG
BACKING PAD WITH VELCRO DIAM 150-180 MM
MAX ROTATION OF 700 RPM
TANK AND WATER TAP ON BOARD
THE TWO MODELS WITH THE FAIRING ALSO HAVE THE REVERSAL OF THE SENSE OF ROTATION THAT ALLOWS TO SHORTEN THE SANDING AND POLISHING TIMES BY AT LEAST 30%
GIVEN THE LOW WEIGHT AND NO CABLE CONSTRAINTS, IT IS EVEN MORE SUITABLE FOR VERTICAL WORKS, AND VERY SPECIFIC FOR WORKING IN CEMETERIES, NOT NEEDING TO BRING GENERATORS
THE VERSION WITH SPEED REGULATOR ALLOWS THEM TO BE VARIED FROM 80 TO 700 RPM
GIVEN ITS LARGE BACKING PAD, IT IS ALSO VERY SUITABLE FOR CRYSTALLIZING MARBLES, OPERATION FACILITATED VERY QUICKLY THANKS TO ITS CHARACTERISTICS
ALTHOUGH IT HAS A LOWER ROTATION THAN THE SINGLE FLEX, IT DOES NOT MAKE PRACTICALLY LESS WORK AS ITS BACKING PAD IS BIGGER THAN THE SINGLE FLEX
IN THE PHOTOS ABOVE ALSO THE SIMPLE VERSION WITHOUT FAIRING, AND WITHOUT REVOLUTION ADJUSTMENT
WATCH THE VIDEOS
https://youtu.be/njLSbFvesCY
https://youtu.be/rcK0I-pjbq8
https://youtu.be/rmdDRjhuU4E
https://youtu.be/pEodg723h0s

All Twister Machines run on an Hydraulic Feeder with a 4HP 220/380V motor.
The Hydraulic Feeder is positioned on a handy trolley in steel that permits the maximum mobility.
It is attached to the machine through pipes 5 mt long.
It also has an oil/water exchanger to guarantee a continous colling.
It can be single-phase or three-phase.

Manual machine for practical and manoeuvrable bush hammering, with 0.37 kW motor at 1400rpm, supplied with 1 bush hammer plate with 4 heads (diameter 150 mm), with grain of choice from the 6 different models available. 2 handgrips provide total control over table work. Equipped with a handle, easy to apply and height-adjustable, it can be used for machining materials already laid on the ground. Total weight 30kg. The tools are made of the highest quality pure widia.

the version with speed regulation and rotation direction inversion with buttons and trimmers
https://youtu.be/wJ0mdiQCCeM
the version with rpm regulation and rotation inversion with display commands or remote control
https://youtu.be/zewfixUwOlE
the version with more powerful 500 w motor, dislpay controls and modifiable side handle
https://youtu.be/Y62boq2mEeQ
always the 500 w version and display commands with the modified side handle, in this case no longer lateral but a throttle type setting
PATENTED TOOL FOR SANDING, POLISHING AND CRYSTALLIZING SMALL SURFACES IN MARBLE, GRANITE AND OTHER
MAKES DOUBLE THAN A NORMAL FLEX
NEW VERSIONS OF THE SINGLE FLEX. WITH BUTTON CONTROLS, OR WITH DISLPAY, OR WITH REMOTE CONTROL
NEW PATENTED VERSION OF THE FLEX WITH ITS WATER TANK
UNIQUE POSSIBILITY TO REVERSE THE DIRECTION OF ROTATION, AND ADJUST THE REVOLUTIONS.
THE FACT OF BEING ABLE TO REVERSE THE SENSE OF ROTATION (NS PATENT) IS AN ABSOLUTE NOVELTY THAT ALWAYS RENEWING THE POINTS OF THE ABRASIVES OR POLISHERS SHORTEN THE PROCESSING TIMES BY AT LEAST 30% AND THE POLISH IS BETTER.
SAFE, QUIET, RELIABLE, EASY TO USE, WORKING IN DIRECT CURRENT WITH ITS SUPPLIED POWER SUPPLY, WITHOUT RISK OF SHOCK
IT WORKS WITH ITS WATER TANK SO ZERO DUST, BUT ALSO VERY LOW SPLASH (NOTHING UP TO 1000 RPM) SO YOU DON'T NEED TO MASK AND START WORKING IMMEDIATELY.
THIS MODEL CAN STILL BE USED FOR VERTICAL WORK AS IT DOES NOT HAVE AN EXCESSIVE WEIGHT. BUT BEING HEAVIER THAN A NORMAL FLEX, IT EATS MORE.
REGULATION OF TURNS FROM 80 TO 3000
AVAILABLE THE FOLLOWING VERSIONS BOTH WITH BUTTON CONTROLS AND ROTATION ADJUSTMENTS, DISPLAY, AND WITH REMOTE CONTROL:
350 W MOTOR HOLDING 100 MM PAD, TOOL WEIGHT 4.7 KG
500 W MOTOR HOLDING BACKING PAD FROM 125 TO 180 MM TOOL WEIGHT 6.3 KG
AVAILABLE BOTH WITH HANDLE TYPE MANETTONE ABOVE THE ENGINE AND WITH SIDE HANDLE, WHILE THE OTHER HANDLE IS ALWAYS REAR
even the model with 350 w motor which normally mounts a pad diameter 100 mm, can also be mounted up to a diameter of 150 mm for certain processes
STILL OTHER MODELS OF THE SINGLE FLEX, AT THE BOTTOM OF THIS PAGE ARE THE REDUCED FLEX, AND THE SINGLE FOR VERTICAL FLEX-
THE REDUCED FLEX HAS IN ADDITION TO THE REVERSAL OF THE SENSE OF ROTATION AND REGULATION OF THE SPINS, THE POSSIBILITY OF MOUNTING A LARGE DISC OF 30 (BUT ALSO 43) CM IN DIAMETER-
WHILE THE FLEX PER VERTICAL IS THE LIGHTEST OF ALL FOR A USE OF THIS KIND
SINGLE FLEX-ANGLE GRINDER FOR MARBLE
THE VERSION WITHOUT SPEED REGULATOR FOR SANDING AND POLISHING MARBLE WITH ITS WATER TANK ON BOARD
THE SINGLE FLEX IS THE VERSION WITH A SINGLE MOTOR COMPARED TO THE DOUBLE FLEX
FOR SANDING AND POLISHING SMALL SURFACES WITHOUT THE MINIMUM DUST
WORKS AT 24V CONTINUOUS
TANK AND WATER TAP ON BOARD
BACKING PAD WITH VELCRO DIAM 100 MM
VERY QUIET, STURDY RELIABLE
WATCH THE VIDEO
https://youtu.be/GfACaVigsqY
MOUNTING PAD M14
BEING LIGHTER THAN THE DOUBLE FLEX, IT IS PERFECTLY PERFECT FOR VERTICAL WORKS
IT CAN ALSO WORK AT 12 V WITH CAR BATTERY THAT GIVES IT 5 HOURS OF AUTONOMY
WE RECENTLY MADE THE VERSION WITH SPEED REGULATOR
THAT ALLOWS TO CHANGE THE ROTATION FROM 80 TO 2800 RPM
YOU CAN USE FOR EXAMPLE:
80-120 REVOLUTIONS TO CRYSTALLIZE
300-500 TO POLISH
2800 REVOLUTIONS TO SAND
UP TO 1000 RPM, THE SPLASH OF WATER IS ALMOST NOTHING
WATCH THE REAL VIDEO
https://youtu.be/bvYtO24ehhw
REDUCED FLEX
https://youtu.be/Wdzx7orsNuc
mounts a 30 cm diameter disc, but can also mount a 43 cm disc.
thanks to its mechanical characteristics it can also withstand a very high weight on it. we can crush as much as we want so that the engine does not slow down.
it has the inversion of the direction of rotation, the regulation of revolutions from 60 to 550 rpm.
for these low rotations it does not dirty anything, there is no need to disguise.
having a large disc and being able to apply a lot of weight is ideal for both polishing and crystallizing.
its maximum speed is the optimal one for polishing with the advantage of the large diameter of the disc.
for example, polishing steps with this particular tool is very easy and fast, alone without help, without dirtying anything,
as even if you have to crystallize steps or other, it is the most comfortable and fastest tool for these things, thanks to its large disc.
the tool like all the others works at 24v with its power supply, and has a water tank and tap on board
weighs 5.7 kg
SINGLE FLEX FOR VERTICAL
https://youtu.be/vGzF4hZ5xq8
with the water tank in position for horizontal work
always with tank for horizontal work
above instead with the water tank and also the tool positioned vertically
always with the tool for vertical work

Multiuse manual machine suitable for ruling, scratching and satin finish on flat surfaces or non-slip work. Can be used to work on marble, granite and concrete. Suitable for work on materials that have already been laid or have not been laid yet. Total weight 10kg.
AVAILABLE MODELS
Ruling machine with discs for non-slip scratching work on marble, granite and concrete. Supplied with 8 diamond disks and spacer.
Ruling machine with roller for non-slip scratching work or for flat surfaces on marble with widia cusps and pitch of choice, 1.5 mm or 2 mm.
Ruling machine with roller for satin finish on flat marble surfaces with electroplated synthetic diamond.

This machine adopt linear guide rail for high precision stone sink hole cutting,faucets hole cutting and sink edge grinding.
Voltage:220V,60HZ/110V,50HZ
Cutting length:900mm
Cutting width:400mm
Main motor power:1800W
Cutting size can be customized according customer requirements
Oval,round and so on sink hole mould is available.

These manual bush hammering tools are the result of our exclusive planning and production processes; different makes and types of edge polishing machine available such as: "BOSCH - FLEX - MAKITA - RUPES" and others on request, all electrically-operated at 1020W with variable speeds from 900rpm to 2000rpm, supplied with a 4-head rotary bush hammer plate with diameter of 150 mm, with grain of choice from the 6 models available. Different machining processes can be carried out, including non-slip sleeve (minimum 50 mm) or free bush hammering on flat surface. Total weight 10kg. The tools are made of the highest quality pure widia and can be reground, thereby lengthening their lifespan.

Manual scratching machine with "Balilla" flexible shaft for scratching work on table. Scratching tools are made of the highest quality pure widia and can be reground, thereby lengthening their lifespan. Systems can also be mounted for satin finishing and manual polishing.
AVAILABLE MODELS
1.5 kW single-phase version, 1 speed. Roller pitch of choice 1.5 mm or 2 mm L= 100mm.
1.5 kW three-phase version, 2 speeds. Roller pitch of choice 1.5 mm or 2 mm L= 100mm

Manual Bush Hammering machine
Midicar with accessories without plate 380V
(on request 220V)

Vacuum diamond core drill Set
With our new Weha diamond drilling set, you are perfectly equipped for smooth and rough surfaces.
Vacuum created by hand pump
Vacuum created by compressed air ejector (you only need a small compressor with about 120 liters per minute delivery)
With control device (manometer) over existing vacuum
rotatable drill column
Stepless height adjustment of the drilling unit on rack
Pre-load of the machine weight by special device on the drill stand
Drilling machine with integrated water flushing bush
Drill to CE standard with PRCD circuit breaker in the cable, integrated for maximum safety
manually switchable mechanical three-speed transmission
exchangeable suction plate
3 speeds (950/1800/3450 rpm)
Connection thread: R1 / 2 "female thread and 1 1/4" UNC male thread
Dimensions base plate with vacuum unit: 540 x 150 mm
Dimensions base plate standard: 500 x 150 mm
Set includes:
1 drill stand with vacuum hand pump and ejector
1 vacuum suction plate and device for connecting a wet vacuum cleaner (wet vacuum cleaner is not included)
1 diamond drill with 1500 watts and 3-speed gearbox in practical storage case
Adapters for other diameter of the drill available as an option

Flex straight grinder H 1127
Long version for optimal handling and hard-to-reach areas.
VE electronic with variable speed preselection and overload protection
Lightweight design for fatigue-free work

Polish your edges and mopboards directly on the construction site. The compact machine is quickly ready for use.
no adjustment of the machine after milling
fast, automatic production of mopboards
great time savings

Standard equipment with grinding wheels out of corundum
including tool support and visibility
pointed profile grinding wheels
Disc width 25 mm
SIC grinding wheels
230 Volt

Manual portable stone edge grinding &polishing machine
Power：220V 50HZ/110V 60HZ
Motor power:2200W
Weight:12KGS
Rotation speed:0-8500r/min

Bush hammer Flex LST 1503 VR
This bush hammer is ideal for light and medium floor work.

full wave electronics with speed preselection, soft start and overload protection
width adjustable in 3-stages, from approx. 40 mm to approx. 92 mm
variable stop for precise working along the stone ridge
dust extraction for the use even in inhabited buildings
the machine, equipped with 60 aggressive carbide tips, is able to perform rough operations quickly and precisely
rotating tool head is mounted in rubber, thereby reducing noise and vibrations increase the service life of the drive
Handle directly above the tool allows precise guidance of the machine

Angle grinder W 10000 230V
Light and strong angle grinder with full-wave electronic. Constant speed irrespective of the load, resulting in higher grinding performance and less abrasive consumption.
Angle grinder in professional quality
Incl. Spindle lock
Incl. protective cover

Angle grinder Supraflex SE 14-2 125
For metal, stone, lacquered surfaces and wood.
steplessly variable speed selection
powerful 1400 Watt motor with fan for optimum cooling
optimized airflow for optimum cooling of the engine and gear.
Set includes:
1 guard SG D125 SE
1 extraction adapter SAD-C D32 AS
1 auxiliary handle SE 14-2 125 M8
1 velcro sanding pad SP D125-8 H/F
1 offset face spanner
1 hexagon socket wrench, SW 4
1 hexagon socket wrench, SW 5 long
1 carrying case L-BOXX 238
1 case insert
3 cable clips
4 sheets of sandingpaper Ø 125 mm

Angle grinder B6
Powerful and robust wet grinder for professional surface processing. Optimal weight distribution for ergonomic work.
spindle lock
water hose with quick coupling
PRCD connector
includes a removable protective hood and 2x carbon brushes

Photomaster CNC Type B
Special machine for engraving pictures, writings, ornaments and other symbols on granite, glass, mirrors, silestone.
Insert directly on the workpiece
Communication via USB port
perfect preparation
easy handling
Engraving time for an engraving 10 x 15 cm: approx. 15 min.
Engraving time for an engraving 20 x 30 cm: approx. 30 -35 min.

The Mimaki Plotter CG60 SR III allows you to scribe fonts or ornaments in just a few minutes and then sandblast them.
Cutting width of 606 mm
500 grams of contact pressure
maximum cutting speed 70 cm/s
can be used with plotter-capable sandblasting films
Width mm 1030
Depth mm 440