Onyx Tile Cutting Machines

These cutting machines, which are structurally identical, process strips up to a width of 620* mm. and thanks to their powerful motors, they cut in a single passage thicknesses up to 40 mm. on granite and 60 mm. on marble. The INT 350 cuts strips up to 3500 mm. long (2000 mm. for the INT 200 model), can mount up to 12 spindles (7 for the INT 200) and it is recommended in high productivity lines.

Upon request, the machine can be equipped with a laser mounted on the disc holder head to show the position where the cut will be performed on the slab.
Trimming machine M744 for strips with useful cutting width up to 900 mm.
Trimming machine M744 for strips with disc diameter 500 mm for cutting thickness up to 120 mm.
Trimming machine M744 for strips to cut formats up to 650 x 650 mm. In this case, the machine is equipped with a squaring system to align each format before the trimming process.
Upon request, all Pedrini M744 trimming machines, both for strips and for slabs, can be equipped with the exclusive cutting system with aligned double disc which allows to directly cut thickness up to 70 mm twice faster than standard versions.
The disc holder head special double support is manufactured in one piece and it ensures the double disc perfect alignment.
The simultaneous use of the two discs allows a high production capacity and a lower tool consumption as well.
Power varying from 4 to 9 kW according to the type of material and to the required thickness.

Single diamond disc machines for the cross cutting of marble or granite strips with predetermined length and for the production of dimensioned elements. The cutting cycle is semi-automatic and it requires the presence of the operator.
The machines can be equipped with several optional to raise the cutting thickness by means of diamond discs with up to 650 mm diameter and to increase the automation level.
These single disc machines for the production of dimensioned elements in marble, granite and natural stones perform strips cross cutting in a way perfectly orthogonal to strips reference side.
Head inverter controlled travelling speed is reduced during the final cutting phase through a sensor system that allows as well for stroke length adjustment. At the end of the cutting stroke, the strip manual positioning zone is left totally free to facilitate operator duty, whilst base sloped configuration conveys water through one sole channel located on machine rear. One control, formed by two buttons that are actuated and held actuated with both hands during the complete cutting cycle, provides the operator totally safe machine use.
The machine structure is made in large thickness normalized steel work.
As a guarantee of assembly perfect geometry, head support fixing plane, orthogonal reference plate fixing plane and entry/exit sides roll shafts mounting bores, have been machined onto monobloc base through one sole positioning on tool machine.
Cuts orthogonally reference plate is built in large thickness hardened steel and is easy replaced. All components have undergone structural inspection through the FEM (Finite Elements Method) and their precision ensures perfect machine geometry.
Machines complete surface is protected by two paint layers applied after sandblasting.
Disc-holder head is assembled onto a group that comprises two large diameter chrome plated and ground parallel rods, that have been stiffened at both ends through strong structures.
The rods slide into two long precise bushings fixed inside the robust support that is assembled onto machine base and is equipped with a simple and precise device for orthogonal adjustment.
A consistently oil lubricated gear-motor and a pinion-rack system drive the cutting stroke whilst a separate pump provides oil lubrication to bushings/rods contact areas.
On board electric panel comprises machine actuating controls and is dust and water proof in accordance to IP 54 (EN 60529) standards.
Machines are equipped with 11 stops pivoting in fixed positions for the cutting of standard dimensions and with an adjustable stop for the cutting of special dimensions and steps.

Automatic cycle multi-disc cross cutting machine for marble or granite strips to produce serial elements with finished length. M747 is available in two main versions to cut strips with up to 2000 mm or 3500 mm length capacity. The number of discs is varying from 5 to 12.
M747 can be also equipped with a wide range of optional for the discs displacement and for big thickness strips cutting.

The Dimension Slab Cutting Line is for cutting stones cut-to-size. It has a machine for cutting the sides and another for cutting the heads. It cuts the strips into dimension stones in one pass efciently.

Hydraulic stone stamping machine CP-90

PGQ-300/400/800 Cutting Machine

PGB-600/800-Double heads cutting Machine