Monoblock 5 Axis Cnc

MONOBLOCK BRIDGE SAW GOLD
HIGH PRECISION 4-AXIS OR 5-AXIS MONOBLOCK BRIDGE SAW
Monoblock bridge saw GOLD
Monoblock bridge saw with automatic head rotation to perform straight cuts in all directions. Manual or automatic head tilt from 90° to 0° for tilted and horizontal cutting with special connection for mounting core drills. High precision head motion on linear guides with recirculating ball slides.
ADVANTAGES
GOLD is the new generation 4 or 5 axis bridge saw for cutting stone slabs:
Customizable according to customer requirements;
Monoblock structure for easy installation (does not require foundation);
Automatic head rotation;
Precision Stone Cutting: extremely accurate and consistent stone sawing.
Simple to Operate: GOLD is capable of fully automatic operation or can be operated in a semi-automatic mode to give the operator full control of sawing operations;
Manual or CNC controlled head tilt from 90 to 0 degrees;
1/2” gas connection for mounting core drills and perform an automatic drilling cycle to easily cut corners and remove the tension from the sintered material plates;
Pre-loaded parametric figures such as hexagon, octagon, kitchen top, trapezium, polygon, etc.
Profiling environment of the CNC to create artistic frames and decorations.

Our MILLENNIUM range is designed for those who are willing to stay one step ahead of the world market and demand total reliability in a CNC machine.
Precision, productivity, efficiency, durability, design and maximum quality worldwide for each of its components, being the most valued equipment over the years.
The first CNC Intelligent equipment was presented for the first time at the ExpoPiedra Madrid 2000-2002 fair under the name of Millennium. After more than 15 years of development and continuous improvement, the new MILLENNIUM range represents the most intelligent machines on the market, Intelligent Performance, being REFERENCES IN THE INTERNATIONAL MARKET.
MILLENNIUM MONOBLOCK CNC 5X
The MILLENNIUM CNC 5-Axis Monoblock Cutter, the top machine in our range, is the reference in the market with more than 250 units installed throughout the world.

Its the new generation of a numerically controlled 5 axes Bridge Saws. Extremely compact and easy to install; it doesnt require any foundations, even as a possibile re-installation. The machine is built with the needs of workshops in mind and it is used for cutting slabs up to 200 mm in thickness (with blade 625 mm) of natural stone, synthetic stone, and ceramic.
Advantages:
- The weight of the machine up to 4.400 kg guarantees high constant precision over time.
- Blade automatic redressing station
- the machine can therefore perform 5-axis machining with a tool and/or disc
- easy programming

Monoblock bridge saw with maximum stability, precision and consolidated technology over the years.
Automatic bridge saw with interpolated 5 axis, machine structure and work table made of hot galvanised dipped electro-welded steel that guarantees high water resistance.
The blade motor has 24 hp - 17.6 kW power, can reach a maximum speed of 4300 Rpm (opt. Tool 6000 Rpm) can cut thicknesses up to 200 mm. with disc max. Ø 625 mm.
Digital brushless type axis drives, coupled with high precision gear motors, linear guides with recirculating balls protected by bellows, allow for extremely precise cuts.
The automatic rotating head 370°, the automatic tilting head from 0° to 90°, a Multi-touch 17” display easy to use, allows to perform orthogonal, sideways, elliptic, circular, tilted, straight, concave, arched convex profiles, solid two and three-dimensional solid excavations are possible exploiting axis interpolation.
The optional tilting work table with hydraulic pump promotes slab loading, speeding up the production process.
Discovery 5 is ideal for indoor and outdoor designs such as kitchen counters, bathroom counters, capitals, tables, sinks, stairs, floors and Funeral art.

The machine combines extreme ease of use and intuitive programming of both basic operations than of the more advanced ones, such as offl ine programming, cad cuts, contouring, profiles and shapes, drilling, coring, bas-reliefs and lettering etc.
Fully interpolated 5 axis movement with rotating head with 370° range, inclination from 0°-90°.
Hot dipped galvanized steel fi xed with saw surface in high density plastic rubber matting (optional) with max blade size of 625 mm (24.6 in) and minimum blade size of 300 mm (11.8 in) with Z axis (rise and fall movement) of 400 mm (15.75 in).
The complete structure is made up of hot dipped galvanized steel structures - supplied with folding door solid panel safety barriers.
Fast and precise movements due to brushless motors with absolute encoders, recirculating ball bearing movement, precision gearboxes and interpolated axis controlled by CNC.
Electro spindle running up to 4500 rpm (6000 on request with center water feed and a 36x2 or ½” gas fitting).
Suspended pendant with 15” TFT color touchscreen. Machine is equipped with USB/Ethernet port for easy loading of programs. Stainless steel electrical panel.
Upon request the machine can also be equipped with parametric drawings, Cuts From CAD, contouring, profiling and shaping, drilling with auto tool changer with magnetic connection, digital camera to provide a jpeg of the slab on screen.
By using the integrated Vacuum head, (upon request) the machine performs automatic movement/unloading of sawn pieces, man power and raw material saving.

Brembana Impact Monoblock 5-axis CNC bridge saw is the right choice for workshops that require a complete machine with minimal investment. It can carry out rectangular, shaped, vertical or inclined cuts, 3D profiling, pocketing, and lettering operations.
This machine is popularly used for cutting marble slabs, granite, synthetic stone, ceramic, and solid stone blocks as well. The monoblock support structure does not require any foundations, which minimizes both the installation and set-up cost.
The weight of the machine, up to 5.7 tons, ensure perfect rigidity for the production of:
*kitchen countertops
*vanity tops
*wall panels for interiors and exteriors
*flooring
*doorsteps, staircases and thresholds
*street furniture
Advantages:
- The weight of the machine up to 5.700 kg guarantees high constant precision over time
- All movements are powered by brushless motors
- the machine can therefore be transformed into a 5-axis machining center
- +33% productivity without manual movements thanks to the vacuum manipulator

Denver Tecnika 5 axes monoblock bridge sawing machine.
The evolution of the most famous high-performance monoblock saw machine on the market.

OZKKM CRUX is a 5-axis monoblock bridge saw machine that, thanks to the advanced functionality, allows every stone fabrication shop to be equipped with accurate and quick machines, without giving up quality. The standard versions of CRUX is monoblock, i.e.: mounted on a monolithic structure of steel carpentry that assures utmost rigidity and stability levels, with no need of any concrete foundation. For this reason, if necessary, they can be easily moved elsewhere. The monoblock configuration can be exploited also for using these machines as “building“ equipment, i.e. it can be placed time by time near the factory where the coating, flooring, etc. are being performed.
OZKKM CRUX is the result of the most advanced designing on computer and the massive use of FEM analysis in order to reach a very high rigidity level of the bridge and structures. Even though it is a sawing machine, both have technical solutions of a CNC machine. All the movements of the axes are on linear bearings which do not need to be adjusted. All the lubrication points have been gathered in areas which can easily be seen and reached, without disassembling guards or protections for facilitating ordinary maintenance. High level components are employed. The motors used are servo motors with precision reducers. Especially the high speed of the X axis allows to cut down idle times as much as possible with a productivity increase (the percentage of the time that the disc stays on the material is higher with respect to the time forplacing or returning to cut start).
The spindle, anchored in front of the beam to offer the utmost rigidity, can accommodate disks up to a diameter of 625 mm and ½” gas thread tools. It also warrants the choice of placing the cutting disc in axis with the head rotation center to reduce the efforts on the axis to zero for an excellent cutting quality. The inclination of the disc can be arranged automatically from 0° to 90° and the possibility to interpolate the X and Y axes make the machine suitable for repetitive processing and single details even with vertical, inclined, parallel, orthogonal, diagonal and curved cuts. The machines, in the standard version are equipped with a fixed table and can be tilted up to 80 ° by a hydraulic piston to facilitate the loading and unloading of the processed pieces.

OZKKM CRUX is a 5-axis monoblock bridge saw machine that, thanks to the advanced functionality, allows every stone fabrication shop to be equipped with accurate and quick machines, without giving up quality. The standard versions of CRUX is monoblock, i.e.: mounted on a monolithic structure of steel carpentry that assures utmost rigidity and stability levels, with no need of any concrete foundation. For this reason, if necessary, they can be easily moved elsewhere. The monoblock configuration can be exploited also for using these machines as “building“ equipment, i.e. it can be placed time by time near the factory where the coating, flooring, etc. are being performed.
OZKKM CRUX is the result of the most advanced designing on computer and the massive use of FEM analysis in order to reach a very high rigidity level of the bridge and structures. Even though it is a sawing machine, both have technical solutions of a CNC machine. All the movements of the axes are on linear bearings which do not need to be adjusted. All the lubrication points have been gathered in areas which can easily be seen and reached, without disassembling guards or protections for facilitating ordinary maintenance. High level components are employed. The motors used are servo motors with precision reducers. Especially the high speed of the X axis allows to cut down idle times as much as possible with a productivity increase (the percentage of the time that the disc stays on the material is higher with respect to the time forplacing or returning to cut start).
The spindle, anchored in front of the beam to offer the utmost rigidity, can accommodate disks up to a diameter of 625 mm and ½” gas thread tools. It also warrants the choice of placing the cutting disc in axis with the head rotation center to reduce the efforts on the axis to zero for an excellent cutting quality. The inclination of the disc can be arranged automatically from 0° to 90° and the possibility to interpolate the X and Y axes make the machine suitable for repetitive processing and single details even with vertical, inclined, parallel, orthogonal, diagonal and curved cuts. The machines, in the standard version are equipped with a fixed table and can be tilted up to 80 ° by a hydraulic piston to facilitate the loading and unloading of the processed pieces.

OZKKM FORNAX is a 5-axis monoblock bridge saw machine that, thanks to the advanced functionality, allows every stone fabrication shop to be equipped with accurate and quick machines, without giving up quality. The standard versions of FORNAX is monoblock, i.e.: mounted on a monolithic structure of steel carpentry that assures utmost rigidity and stability levels, with no need of any concrete foundation. For this reason, if necessary, they can be easily moved elsewhere. The monoblock configuration can be exploited also for using these machines as “building“ equipment, i.e. it can be placed time by time near the factory where the coating, flooring, etc. are being performed.
OZKKM FORNAX is the result of the most advanced designing on computer and the massive use of FEM analysis in order to reach a very high rigidity level of the bridge and structures. Even though it is a sawing machine, both have technical solutions of a CNC machine. All the movements of the axes are on linear bearings which do not need to be adjusted. All the lubrication points have been gathered in areas which can easily be seen and reached, without disassembling guards or protections for facilitating ordinary maintenance. High level components are employed. The motors used are servo motors with precision reducers. Especially the high speed of the X axis allows to cut down idle times as much as possible with a productivity increase (the percentage of the time that the disc stays on the material is higher with respect to the time forplacing or returning to cut start).
The spindle, anchored in front of the beam to offer the utmost rigidity, can accommodate disks up to a diameter of 900 mm and ½” gas thread tools. It also warrants the choice of placing the cutting disc in axis with the head rotation center to reduce the efforts on the axis to zero for an excellent cutting quality. The inclination of the disc can be arranged automatically from 0° to 90° and the possibility to interpolate the X and Y axes make the machine suitable for repetitive processing and single details even with vertical, inclined, parallel, orthogonal, diagonal and curved cuts. The machines, in the standard version are equipped with a fixed table and can be tilted up to 80 ° by a hydraulic piston to facilitate the loading and unloading of the processed pieces.