Stone quarrying hydro bags are widely used in natural stone (marble, granite, basalt) quarrying to separate blocks from large masses in quarries. Hydro bags allow blocks of 1000 tons or more to be scrapped without the need to prepare slots to house jacks. The original thickness of the water bag is only 2 mm (0.08"), it can easily slip into a wire saw cut.
Quarry Hydro bags, also known as Water Bags, are expanding hydraulic cushions composed of two high tensile steel plates. The water bags expand under the pressure of pumped water at 30-40 bar, allowing a maximum expansion of 25-30 cm (approximately 1') and a thrust of up to 1000 tons.
The Hydro-bag is environmentally friendly as only running water (not oil as in hydraulic jacks) is the dilatation fluid. It is safe, even if the hydro-bag's cushion blows due to excessive inflation pressure there is no deflagration because water, not air, is the inflating media. The Hydro-bag does not require any maintenance, throw it away when it is no longer usable.
The thrust that can be obtained for a pillow can be up to 1000 tons. Combine two or more pads to achieve higher performance; side by side or together in packs.
The quarry hydraulic rock splitter consists of splitting cylinders and a power unit. Cylinders are powered by the high pressure power unit. Fuel tank piston and wedges are the main component of the cylinder. It needs a pre-drill hole of required depth down on the material for movement of the middle wedge. There is a valve on the top of cylinder to control piston work, when the power unit give pressure make the piston work, piston will pressure middle wedge move into bottom, and at the same time, middle wedge will push counter wedges move to sides, a huge horizontal splitting force is produced against to the hole wall, when the tension increases beyond the tensile strength of the material, a split will occur.
Suitable for pushing over the quarry stone after the cut is made by the diamond wire; Extremely slim makes it easy to be put into the cut made by diamond wire; Reusable for cost savings
The capstone airbag is one of the special tools for pushing or knocking down large blocks of blocks after cutting with a diamond wire saw in stone mining. The thickness of the capstone airbag is less than 7mm, and it is easy to put into the seam after cutting by the diamond wire saw. Use the mine air compressor to inflate the airbag, and the airbag expands, and the large stones are easily pushed away and pushed unscathed. It can be used many times; the company has long-term cooperation with many
Suitable for pushing over the quarry stone after the cut is made by the diamond wire; Extremely slim makes it easy to be put into the cut made by diamond wire; Reusable for cost savings.
Type: Stone Quarry Machines › Quarry Hydro-Bags, Rock Splitter › Quarry Hydro-Bags
Warranty: 3 Months
Usage: Granite, Marble, Limestone, Sandstone
Machinery Function Features:
Hydrobags are supplied in the standard measures 500×500 – 750×750 – 1000×500 – 1000×1000 – 1500×1500 mm. DEFAULT SIZES : Model Sizes C500 50X50 cm C750 75X75 cm C1000 100X100 cm C1500 150X150 cm C500x1000 50×100 cm Centralina idraulica per Hydrobag, fornita completa di filtro acqua, manometro, tubi e innesti rapidi. La centralina può alimentare contemporaneamente 3 cuscini. Hydraulic unit for hydrobag, is supplied complete with water filter, pressure gauge hoses and quick connectors; the control
Hydrobag is a pump for filling cushion with water, for borrow material excavation. Hydro bag is composed by: - pressure power unit Hydro bag with electric engine 5,5 Hp - supported wheelbarrow and water reservoir - safety and distribution valves - aspiration and pressure pipes and aspiration filter - Series of fast couplings - thrust up to 1000 tonnes, dilatation 25-30cm - supply plug and engine - saver interrupter. Cushions are available: CM 50x50, CM 80x80, CM 50X100, CM 100x100, CM 150x150.
THE HYDRO (WATER) BAG IS MANUFACTIRED FROM THE FINEST HIGH QUALITY TENSILE STEEL , HEREBY QUARANTEEING FLAWLESS PERFORMANCE .THE BAG IS INSERTED IN THE CRACK IN THE BLOCK AND IT SEPARATED THE BLOCK AS S0ON AS WATER IS INSERTED IN THE BAG WITH THE HELP OF THE WATER PUMP. DIMENSION 1 * 1 MTR 1 * 0.5 MTR
Nowadays, most mining and quarrying industries utilize a diamond wire saw machine for bench cutting operations. This method uses a metal wire or cable assembled by diamond beads to cut the hard stone into large blocks. Many parameters classied into controllable and uncontrollable parameters aect the performance of the diamond wire saw cutting meth-od. The uncontrollable parameters are related to rock engineering properties, and controllable parameters are related to operational aspects and mac
red polymer marble block push air bag for various quarry 1.Air pushing bag 2.put into the aperture easily 3.Strong pushing power 4.Max capacity:200 tons 5.can be used for many times Pushing air bag is often used in stone quarrying after cutting by wire saw. High-materials and special processing technique. The characters of our air bags: 1. Less than 7mm thickness 2. Strong pushing power 3. High-tech materials and special processing techniques 4. No frequent problem in split and damage 5. Can be
Bestlink Factory Price Quarry Block Air Bag Pushing for Marble Granite Quarry block pushing air bag is used to separate the marble, granite, stones (rock mass) block from the basic rock achieving a maximum opening of 45-120cm at the top. The air bag can separate the block (rock mass) which is having all side wire saw cut faces. The standard configuration set contains two air bags, with one set of air hose & air control panel. Our air pushing bag is manufactured with high-tech materials and proce
The steel cushion Hydro-Bag is widely used in the marble and stone quarrying industry,specially for stripping blocks from the mountain. The revolutionary aspect of the HYDRO-BAG equipment lies basically in the possibility of stripping blocks up to 1000 tons or more, without the need to prepare slots to house the jacks since the HYDRO-BAG has an original thickness of just 2 mm (0.08") and can be easily slipped into the wire saw cut. A complete HYDRO-BAG equipment consists of: 1. Electric or pneum
Type: Stone Quarry Machines › Quarry Hydro-Bags, Rock Splitter › Quarry Air Pushing Bags
Warranty: 3 Months
Usage: Granite, Marble
Machinery Function Features:
Hot Sale Pushing Air Bag for Marble and Granite Block Cutting 1.Air pushing bag 2.put into the aperture easily 3.Strong pushing power 4.Max capacity:200 tons 5.can be used for many times Pushing air bag is often used in stone quarrying after cutting by wire saw. High-materials and special processing technique. The characters of our air bags: 1. Less than 7mm thickness 2. Strong pushing power 3. High-tech materials and special processing techniques 4. No frequent problem in split and damage 5. Ca
Air pushing bag is used to push over stone blocks after diamond wire saw cutting. The thickness of our air bag is only 5-7mm, which can be put into the cutting crevice easily. After inflating the air pushing bag by air compressor, it could generate 50-260 tons pushing power according to the different size air bags. Such huge pushing power can push over the big block easily. BESTLINK air pushing bag is made of high quality raw material. It's durable and repairable. It's the most efficient pushing
Manufacturers of Mining Equipment China Gold Quarry Stone Machine Block Pushing Air Bag Quarry block pushing air bag is used to separate the marble, granite, stones (rock mass) block from the basic rock achieving a maximum opening of 45-120cm at the top. The air bag can separate the block (rock mass) which is having all side wire saw cut faces. The standard configuration set contains two air bags, with one set of air hose & air control panel. Our air pushing bag is manufactured with high-tech ma
Type: Stone Quarry Machines › Quarry Hydro-Bags, Rock Splitter › Quarry Hydro-Bags
Warranty: 6 Months
Usage: Marble, Limestone, Sandstone
Machinery Function Features:
The steel cushion Hydro-Bag is widely used in the marble and stone quarrying industry,specially for stripping blocks from the mountain. The revolutionary aspect of the HYDRO-BAG equipment lies basically in the possibility of stripping blocks up to 1000 tons or more, without the need to prepare slots to house the jacks since the HYDRO-BAG has an original thickness of just 2 mm (0.08") and can be easily slipped into the wire saw cut. A complete HYDRO-BAG equipment consists of: 1. Electric or pneum
Type: Stone Quarry Machines › Quarry Hydro-Bags, Rock Splitter › Quarry Air Pushing Bags
Warranty: 3 Months
Usage: Granite, Basalt, Quartzite
Machinery Function Features:
Products Features The Pushing Air Bag is manufactured with high-tech materials and processed by special techniques, no frequent problem in split or damage reusable. The standard configuration set: Each set contains two air bags, with one set of air pipe & air control panel. Application It performs primely and is suitable for blocks splitting after wire saw cutting in quarry. Polymer blocks pushing air bag is used to separate the marble, granite, stones(rock mass) block from the basic rock achiev
Granite/marble stone block pushing polymer air bag Polymer blocks pushing air bag is used to separate the marble, granite, stones(rock mass) block from the basic rock achieving a maximum opening of 45cm at the top. The air bag can separate the block (rock mass) which is having all side wire saw cut faces. The standard configuration set: Each set contains two air bags, with one set of air pipe & air control panel.
It can be used to used to separate the marble, granite, stones(rock mass) block from the basic rock achieving a maximum opening of 45cm at the top. The air bag can separate the block (rock mass) which is having all side wire saw cut faces. The thickness of our air bag is less than 7mm. It can be put into the cutting aperture easily. Aerated the air bag with the air compressor, the inflation of air bag can bring pushing power which can be from 20 to 200 tons according to different size of bag. Th
Type: Stone Quarry Machines › Quarry Hydro-Bags, Rock Splitter › Quarry Air Pushing Bags
Warranty: 3 Months
Usage: Granite, Marble, Limestone, Slate
Machinery Function Features:
marble granite quarry block pushing down air bag Quarry block pushing air bag is used to separate the marble, granite, stones (rock mass) block from the basic rock achieving a maximum opening of 45-120cm at the top. The air bag can separate the block (rock mass) which is having all side wire saw cut faces. The standard configuration set contains two air bags, with one set of air hose & air control panel. Our air pushing bag is manufactured with high-tech materials and processed by special techni
Description:qarry blocks pushing air bag is used to separate the marble, granite, stones(rock mass) block from the basic rock achieving a maximum opening of 45cm at the top. The air bag can separate the block (rock mass) which is having all side wire saw cut faces. The standard configuration set: Each set contains two air bags, with one set of air pipe & air control panel. Product features: Quarry blocks pushing air bag is used to separate the marble, granite, stones(rock mass) block from the ba
Type: Stone Quarry Machines › Quarry Hydro-Bags, Rock Splitter › Quarry Hydro-Bags
Warranty: 12 Months
Usage: Granite, Marble
Machinery Function Features:
Hydro Bag The Hydro (Water) bag is manufactured from the finest quality high tensile steel. Hereby guaranteeing flawless performance. The bag is inserted in the crack in the block and it separates the block. Machine is equipped with 2 HP.AC. motor. Hydro bag is operated with Water pump. It is use and throw type bag. It's usable for one time.
Description:at the time of 1st splitting gas available for jumop size quarry blocks after expansive mortar working over , Specifically for stripping blocks from the mountain. Its name is hydro steel water bag . Hydro-Bag is a simple, versatile and economical tool that has revolutionized quarry block stripping thanks to all the positive advantage. 1.Elimination of the time necessary for the preparation of the slots of the jacks 2.The blocks of stone are obtained with their sections intact, withou
Hydro-bag This has happened in the marble and stone quarrying industry , specifically for stripping blocks from the mountain . HYDRO-BAG has completely upset bench excavation in quarries . The revolutionary aspect of the HYDRO-BAG equipment lies basically in the possibility of stripping blocks up to 1000 tons or more , without the need to prepare slots to house the jacks since the HYDRO-BAG has an original thickness of just 2 mm ( 0.08) and can be easily slipped into the wire saw cut . Crack-roc
Splitting cushions in polyester material spread with PVC and FH sealed. Instertable in size of 9mm with adequate protective sheet. Maximum inflated pressure 3 Atm. Max. split to a limit of 45 cm.Complete with an inflatable centre suitable for the use of maximum of 3 cushions simultaneously.
HYDRO BAG Tipping cushions using high pressure water HIDRO-BAG offer the following advantageous: features: -doesnt ruin the block -weight a mere 8 kg - it is only 2mm thick -can be iserted in the diamond r helicoidal saw cut -has a thrust development of 300 tons -works with water, at 30 atm only. -it is provided whit rapid coupling -does not required maintenance -can be thrown after use
This has happened in the marble and stone quarrying industry , specifically for stripping blocks from the mountain . HYDRO-BAG has completely upset bench excavation in quarries . The revolutionary aspect of the HYDRO-BAG equipment lies basically in the possibility of stripping blocks up to 1000 tons or more , without the need to prepare slots to house the jacks since the HYDRO-BAG has an original thickness of just 2 mm ( 0.08 ) and can be easily slipped into the wire saw cut .
Product Overview This quarry hydro-bags, rock splitter is supplied by Quanzhou DAFON Machinery as a working production machine for stone workshops and quarries. It is configured to the buyer's own working size and voltage before shipment, and it is run from its own control panel. How It Works The operator sets the working values on the machine panel, loads the workpiece, and the cycle runs without further adjustment. Feed and speed are set per stone, so the same machine moves between a hard gran
Product Overview This quarry hydro-bags, rock splitter is supplied by Quanzhou DAFON Machinery as a working production machine for stone workshops and quarries. It is configured to the buyer's own working size and voltage before shipment, and it is run from its own control panel. How It Works The operator sets the working values on the machine panel, loads the workpiece, and the cycle runs without further adjustment. Feed and speed are set per stone, so the same machine moves between a hard gran
Type: Stone Quarry Machines › Quarry Hydro-Bags, Rock Splitter › Quarry Air Pushing Bags
Warranty: 3 Months
Usage: Granite, Marble, Limestone, Slate
Machinery Function Features:
marble granite quarry block pushing down air bag Quarry block pushing air bag is used to separate the marble, granite, stones (rock mass) block from the basic rock achieving a maximum opening of 45-120cm at the top. The air bag can separate the block (rock mass) which is having all side wire saw cut faces. The standard configuration set contains two air bags, with one set of air hose & air control panel. Our air pushing bag is manufactured with high-tech materials and processed by special techni
Nowadays, most mining and quarrying industries utilize a diamond wire saw machine for bench cutting operations. This method uses a metal wire or cable assembled by diamond beads to cut the hard stone into large blocks. Many parameters classied into controllable and uncontrollable parameters aect the performance of the diamond wire saw cutting meth-od. The uncontrollable parameters are related to rock engineering properties, and controllable parameters are related to operational aspects and mac
Stone quarrying hydro bags are widely used in natural stone (marble, granite, basalt) quarrying to separate blocks from large masses in quarries. Hydro bags allow blocks of 1000 tons or more to be scrapped without the need to prepare slots to house jacks. The original thickness of the water bag is only 2 mm (0.08"), it can easily slip into a wire saw cut.
Quarry Hydro bags, also known as Water Bags, are expanding hydraulic cushions composed of two high tensile steel plates. The water bags expand under the pressure of pumped water at 30-40 bar, allowing a maximum expansion of 25-30 cm (approximately 1') and a thrust of up to 1000 tons.
The Hydro-bag is environmentally friendly as only running water (not oil as in hydraulic jacks) is the dilatation fluid. It is safe, even if the hydro-bag's cushion blows due to excessive inflation pressure there is no deflagration because water, not air, is the inflating media. The Hydro-bag does not require any maintenance, throw it away when it is no longer usable.
The thrust that can be obtained for a pillow can be up to 1000 tons. Combine two or more pads to achieve higher performance; side by side or together in packs.
The quarry hydraulic rock splitter consists of splitting cylinders and a power unit. Cylinders are powered by the high pressure power unit. Fuel tank piston and wedges are the main component of the cylinder. It needs a pre-drill hole of required depth down on the material for movement of the middle wedge. There is a valve on the top of cylinder to control piston work, when the power unit give pressure make the piston work, piston will pressure middle wedge move into bottom, and at the same time, middle wedge will push counter wedges move to sides, a huge horizontal splitting force is produced against to the hole wall, when the tension increases beyond the tensile strength of the material, a split will occur.
Ask a Question
Could not find the answer you need? Ask about Quarry Hydro Bag.
What is Quarry Hydro-Bags maximum thrust force?View answer⌄
Asked by Visitor
The hydro bags expand under the pressure of water pumped at 30-40 bar, permitting a maximum dilatation of 25-30 cm (approx. 1’) and a thrust force up to 1000 tons. Couple two or more cushions to obtain higher performances; side by side or combined together in packs.
The working principle of quarry rock splitter is based on two counter wedges inserted in a pre-drilled hole. A hydraulic cylinder pushes out a centre wedge between the counter wedges to spread them apart and the rock is forced to crack.